Outlaw Audio 1070 User Manual download pdf (Page 36)

Outlaw Audio

Owner’s Manual

System Conﬁguration Settings

This ﬁnal sub-menu lets you adjust some convenience and comfort parameters

that enable you to enjoy the Model 1070 even more by custom tailoring key

settings. Note that some of these settings may require a bit of experience with

the Model 1070 in its factory default mode before you decide which to change,

and to what degree the changes should be made. If you are in a rush to get your

new Model 1070 into action, there is no problem in leaving the factory settings

in place and returning to this menu later to make the desired changes.

1. Press the MENU button on the front panel or the remote to display

the Main Menu.

The Main Menu appears on-screen:

MAIN MENU

> INPUT CONFIG

SPEAKER SIZE

SPEAKER X-OVER

SURROUND CONFIG

CHANNEL CALIBRATION

DELAY ADJUST

SYSTEM CONFIG

EXIT

2. Move the cursor to SYSTEM CONFIG by using the and buttons

on the front panel or remote.

3. With the cursor pointing to

SYSTEM CONFIG, press SET on the

front panel or the remote.

The Channel Calibration sub-menu appears:

SYSTEM CONFIG

> OSD TIME OUT :3OSEC

DISPLAY TIME OUT :ON

VOLUME DEFAULT :LAST

DEFAULT VOL :-25dB

SLEEP :OFF

RETURN TO MAIN MENU

OSD (On-screen display) Time Out

This setting determines the length of time that the on-screen messages (vol-

ume change, input selection, surround mode, etc.) appear on the on-screen

display.

To adjust the OSD time out:

1. From the SYSTEM CONFIG menu, press or to move the cursor

OSD TIME OUT.

2. Press the

and buttons on the front panel or remote to select

the desired setting.

The available choices are:

5SEC



10SEC



15SEC



20SEC



25SEC



30SEC

Display Time Out:

This setting determines if the on screen messages and setup menus time out

(disappear from the screen) after the length of time selected in the OSD TIME

OUT line, as shown above. In most cases you will want to use the ON setting.

However, when making adjustments during the setup process, you may want

to leave the menus on until you intentionally turn them off.

To set display time out:

1. From the SYSTEM CONFIG menu, press or to move the cursor

DISPLAY TIME OUT.

2. Press the

and buttons on the front panel or remote to toggle

between ON and OFF.

Selecting

(default) will cause on-screen messages to disappear after

the time period set in OSD Time Out.

Selecting

OFF

will make on-screen messages remain visible until the

Menu button on the remote or front panel is pressed.

Volume Default

This setting determines the volume level when the Model 1070 is turned on.

To set the Volume Default:

1. From the SYSTEM CONFIG menu, press or to move the cursor

VOLUME DEFAULT.

2. Press the

and buttons on the front panel or remote to toggle

between

LAST and ON.

Choose

LAST

(default) to have the Model 1070 always turn on at the

same volume level in place when it was turned off.

Choose

to always have the Model 1070 play at the level speciﬁed in

Default Volume each time you turn it on.

Default Volume

If you selected ON in the VOLUME DEFAULT menu above, your Model 1070

will always turn on at the same volume. Use the Default Volume setting to

enter that volume level.

To set the Default Volume level:

1. From the SYSTEM CONFIG menu, press or to move the cursor

DEFAULT VOLUME.

2. Press the

and buttons on the front panel or remote to select

the desired setting.

You can adjust the level from -70 to +10dB.

Keep in mind that a -70dB setting will be below your threshold of hearing

and +10dB may well make your ears bleed.

We suggest something in the range of -30 dB. That way, you’ll be sure

to know that your system’s on and working.

System Setup

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 51 52

Comments to this Manuals

No comments

Outlaw Audio 1070 User Manual Page 36

Comments to this Manuals