Outlaw Audio 1070 User Manual download pdf (Page 28)

Outlaw Audio

Owner’s Manual

Setting the Level Trim:

To conﬁgure the Level Trim of a video input:

1. Move the cursor to

LEVEL TRIM by using the and buttons on

the front panel or remote.

2. Press the

and buttons on the front panel or remote to scroll

through the preferred level trim for this input.

The input choices appear as follows as you scroll through them:

0dB-6dB-12dB

These choices allow you to adjust relative audio levels so that when you

switch from one source to another, you won’t be subjected to a wide

disparity in volume. We suggest that you accept the “0dB” default for

each input and make changes only after you determine that an input

needs “trimming.”

Setting Auto Polling

To conﬁgure the Auto Polling of a video input:

1. Move the cursor to

AUTO POLL by using the and buttons on

the front panel or remote.

2. Press the

and buttons on the front panel or remote to toggle

between ON and OFF.

When

is selected the Auto Poll circuitry will automatically switch

the audio input from the selected digital source to the analog input for

the source when the digital data stream is interrupted. This is helpful

for use with digital cable boxes where the audio switches between digital

and analog, depending on which channel is selected.

When

OFF

is selected the Model 1070 will keep the digital input active

even when the digital data is interrupted. This is the preferred setting

for the DVD input where the digital audio stops during menu setup or

when a disc is paused.

Setting Bass and Treble

You’ll make both these tone control adjustments in the same way.

To conﬁgure the Bass or Treble of a video input:

1. Move the cursor to

BASS (or TREBLE) by using the and buttons

on the front panel or remote.

2. Press the

and buttons on the front panel or remote to scroll

through the preferred tone control settings for this input.

The input choices for both Bass and Treble appear as follows as you

scroll through them:

-6dB-5dB-4dB-3dB-2dB-1dB0dB1dB2dB

3dB4dB5dB6dB

Setting Lip Sync Delay

Digital video sources and displays will often use extensive video processing

for scaling or in transmission paths that may cause the video on your screen

to lag behind the audio. The amount of this delay will vary with a number of

factors, but the Model 1070 lets you delay the audio to ﬁx this problem. It also

lets you set a different lip sync delay time for each input.

To conﬁgure the Lip Sync Delay of a video input:

1. Move the cursor to

LIP SYNC DELAY by using the and buttons

on the front panel or remote.

2. Press

to increase the amount of lip sync delay, or to decrease it.

Up to 200ms of delay can be selected in 10ms increments.

Choosing Another Input

To select another input from the Input Conﬁguration sub-menu:

1. Move the cursor to

RETURN TO INPUT MENU by using the and

buttons on the front panel or remote.

2. Press SET on the front panel or the remote.

The Input Conﬁguration sub-menu appears.

3. Move the cursor to the new input that you want to conﬁgure by

using the

and buttons on the front panel or remote.

4. Press SET on the front panel or the remote.

You’ll see the same conﬁguration sub-menu as you did for the DVD input.

You’ll conﬁgure the remaining video inputs (Video 1-4) by following

the same procedures. Remember that the DVI 2 connector is available

only when you’ve selected the Video 2 input.

Conﬁguring Audio Inputs

In general, the procedures for conﬁguring Audio inputs (Tuner, CD, Tape,

and Aux) are very similar to those for conﬁguring Video inputs. Two major

differences are:



You can’t choose a video input for any of the four audio sources (the menu line

is there but the only choice is “None”)



There is no Lip Sync Delay available for audio-only sources

Proceed with conﬁguring the tuner and remaining audio components con-

nected to your Model 1070. Once you have completed the input conﬁguration

process for all inputs, your next step is to conﬁgure the Model 1070 to match

the number and type of speakers in your system.

To return to the Main Menu:

1. Move the cursor to RETURN TO MAIN MENU by using the

and

buttons on the front panel or remote.

2. Press SET on the front panel or the remote.

The Main Menu appears.

Speaker Placement

Before we get to the Speaker Size sub-menu, it is worth mentioning that you

should understand that correct speaker placement is critical to good sound.

Then again, also understand that there are no hard and fast laws governing

where you should put them!

Frustrating, right? The good news is that there are several guidelines you

can follow. Unfortunately, every listening room and combination of speak-

ers exhibits different acoustic qualities, so what works in one situation won’t

necessarily work in another. So, you’ll probably have to experiment a bit before

you’re really happy with your system’s sound. That being said, here are some

pointers to follow.

System Setup

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 51 52

Comments to this Manuals

No comments

Outlaw Audio 1070 User Manual Page 28

Comments to this Manuals