Outlaw Audio 1070 User Manual download pdf (Page 3)

Model 1070 7.1 Channel Surround Sound Receiver

Owner’s Manual

Precautions

Verify The Line Voltage

Your new Model 1070 has been factory conﬁgured for 120 (+/- 3%) volt AC lines. Connecting

the unit to a line voltage other than that for which it is intended can create a safety and

ﬁre hazard, and may damage the Model 1070. If you have any questions about the voltage

requirements for your speciﬁc model, or about the line voltage in your area, contact Outlaw

Audio before plugging the unit into a wall outlet.

NOTE: It is always a good idea to avoid using any audio or video equipment on

the same AC circuit as equipment with motors, such as air conditioners or refrig-

erators. This will lessen the possibility of power variation and electrical start-up

noise affecting your sound system.

Power Cord

The removable power cord that is shipped with the Model 1070 is speciﬁcally designed to

be used with this product. DO NOT use any other power cord, as that may reduce the unit’s

performance and possibly create a safety hazard. In particular, DO NOT use standard IEC

type power cords designed for computers and other business equipment products, as they

have a three prong plug that is not meant for use with the 1070. Should the power cord

require replacement, use an identical type, or contact Outlaw Audio for service.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug, never pull

the cord. If you do not intend to use the Model 1070 for any considerable length of time,

disconnect the plug from the AC outlet. If the power cord is replaced, make certain that it is

of similar gauge. As with all electrical devices, do not run power cords under rugs or carpets

or place heavy objects on them. Damaged power cords should be replaced immediately

with cords meeting factory speciﬁcations.

AC Fuse

The fuse is located inside the chassis and is not user-service-able. If power does not come

on, contact your authorized service station.

Wiring

Cables that are run inside of walls should have the appropriate markings to indicate com-

pliance with, and listing by the UL , CSA or other standards required by the UL, CSA, NEC

or your local building code. Questions about cables inside of walls should be referred to a

qualiﬁed custom installer, or a licensed electrician or low-voltage contractor.

Installation Location

To assure proper operation and to avoid the potential for safety hazards, place the unit

on a ﬁrm and level surface capable of supporting it’s weight. When placing the unit on a

shelf, be certain that the shelf and any mounting hardware can support the weight of the

unit and any additional items in the equipment rack, or on the shelf.

When positioning the Model 1070 in its ﬁnal location, make certain that it has adequate

ventilation on all sides, as well as on the top and bottom. In particular, it is a good idea

to provide at least two or three inches of room above the unit for air circulation. DO NOT

place CDs, DVDs, videotapes, owner’s manuals, or other paper on top of, or beneath, the

unit, or in-between multiple ampliﬁers in a stack. This will block airﬂow, causing heat

build-up, degraded performance, and may create a possible ﬁre hazard.

If the unit is to be enclosed in a cabinet or rack, make certain there is adequate air cir-

culation. Sufﬁcient ventilation should be provided so that hot air may exit, and cool air

may enter the cabinet. In some instances, a small cooling fan may be required to insure

adequate airﬂow through the cabinet. If you are in doubt as to the ventilation require-

ments for your speciﬁc installation, please contact us. Also, do not place the Model 1070

directly on a carpeted surface, as this will inhibit airﬂow underneath as well as create a

potential ﬁre hazard.

Avoid installation in humid locations, in extremely hot or cold locations, or in areas that

are exposed to direct sunlight or space heating equipment.

Do Not Open The Cabinet

There are no user serviceable components inside this product. Opening the cabinet may

present a shock hazard, and any modiﬁcation to the product will void your guarantee. If

water or any metal object, such as a paper clip, coin or a staple, accidentally falls inside

the unit, disconnect it from the AC power source immediately, and contact Outlaw Audio

for further instructions.

Recording Copyright

Recording of copyrighted material for other than personal use is illegal without permission

of the copyright holder.

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of

the NEC, ANSI/NFPA 70, which provides guidelines for proper grounding and, in particular,

speciﬁes that the cable ground shall be connected to the grounding system of the building,

as close to the point of cable entry as practical.

FCC Information for User

CAUTION

: ANY changes or modiﬁcations not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

NOTE

: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Outdoor Antenna Installation

Safe Antenna and cable Connection

If an outside antenna or cable system is connected to the equipment, be sure the an-

tenna or cable system is grounded so as to provide some protection against built up static

charges and voltage surges. Section 810 of the

national Electrical Code, ANSI/NFPA 70

(in Canada, part 1 of the Canadian

Electrical Code) provides

information with

respect to proper

grounding of the

mast and sup-

porting structure,

grounding of the

lead-in wire to an

antenna discharge

un it , si ze of gr ou nd in g

conductors, location of antenna discharge

unit, connection to grounding electrodes and

requirements for the grounding electrode.

Keep Antenna Clear of High Voltage Power Lines or Circuits

An outside antenna system should be located well away from power lines, electric light or

power circuits and where it will never come into contact with these power sources if it should

happen to fall. When installing an outside antenna, extreme care should be taken to avoid

touching power lines, circuits or other power sources as this could be fatal. Because of the

hazards involved, antenna installation should be left to a professional.

Precautions

1 2 3 4 5 6 7 8 ... 51 52

Comments to this Manuals

No comments

Outlaw Audio 1070 User Manual Page 3

Comments to this Manuals