Outlaw-audio 970 User Manual download pdf (Page 38)

Outlaw Audio

Owner’s Manual

Lip-Synch Delay

Because video is more data-intensive than audio, processing video takes longer. As

a result, sometimes the video will lag behind the audio, causing a lip sync error.

The problem may vary with each source device. In particular, digital TV tuners

(or the stations they receive) seem to cause lip sync problems more than do DVD

players. The Model 970 lets you delay the audio to ﬁx this problem. It also lets you

set a different lip sync delay for each input, in increments of 10 milliseconds.

You can adjust lip sync delay for a speciﬁc video input directly from the remote

or from the Input Conﬁguration Menu (see page 26). Lip sync delay is not

available for audio-only inputs.

To set lip sync delay from the remote:

1. Press the SYNC button on the remote.

The current Lip Sync delay for the input in use will appear on the bottom

line of the front panel display and the on screen message (unless you

have selected OSD: OFF in the Input Conﬁguration menu).

2. Press the or buttons on the remote to adjust the amount of

delay being applied.

Watching a close-up of an actors’ lips while carefully listening to their

dialogue is the best way to set the proper amount of lip sync delay.

If you hear dialog before you see lips moving, increase the delay time.

If you see lips moving before you hear dialog, decrease the delay time.

3. Press SET to choose the new lip sync setting.

Adjusting Tone Controls

You can adjust the bass and treble for a speciﬁc input directly from the remote

or from the Input Conﬁguration Menu (see page 26). The maximum boost

or cut is ±6dB.

To adjust tone controls:

1. Press the TONE button on the front panel or remote.

The current setting for Treble boost or cut will appear in the lower line

of the front panel and on screen display (unless you have selected OSD:

OFF in the Input Conﬁguration menu.)

2. Press the or buttons on the front panel or remote to increase

the boost or cut of the Treble as desired.

The input choices for both Bass and Treble appear as follows as you

scroll through them:

-6dB-5dB-4dB-3dB-2dB-1dB0dB1dB2dB

3dB4dB5dB6dB

3. When the desired boost or cut is set, press the TONE button again

to toggle from Treble to Bass.

4. Press the

or buttons on the front panel or remote to increase

the boost or cut of the Bass as desired.

5. Press the SET button on the front panel or remote when you are

ﬁnished with the tone control adjustments.

Using the AM/FM Tuner

The Model 970 incorporates an AM/FM/FM stereo tuner with 30 station-memory

presets. You can mix AM and FM presets as you wish. Stations can also be

tuned manually. To use the tuner, you must connect antennas to the AM and

FM antenna terminals on the back of the unit (see page 18).

To select the AM/FM tuner as your source:



Press AM/FM on the remote or TUNER on the front panel.

The band and frequency will appear on the bottom line of the front

panel display and in the on-screen messages (unless you have selected

OSD: OFF in the Input Conﬁguration menu).

To change the frequency (station) manually:



Press CHANNEL UP or CHANNEL DOWN on the remote control, or

the or buttons on the front panel.

The band and frequency will appear on the bottom line of the front

panel and on-screen display (unless you have selected OSD: OFF in the

Input Conﬁguration menu.)

To scan for the next frequency (station) automatically:



Press CHANNEL UP or CHANNEL DOWN on the remote control,

or the

or buttons on the front panel. Hold the button down

for one second, then release it.

The tuner will automatically scan up or down to the next active fre-

quency. The band and frequency will appear on the bottom line of the

front panel and on-screen display (unless you have selected OSD: OFF

in the Input Conﬁguration menu.)

To enter a frequency (station) directly:

1. Press DIRECT on the remote.

The current frequency will go blank on the bottom line of the front

panel and on-screen displays.

2. Use the 10-key numerical keypad on the remote to enter the

desired frequency.

For example, to enter 89.3 FM, simply punch in 0893.

3. Press SET on the remote.

To change the band (AM or FM):



Press AM/FM on the remote or TUNER on the front panel.

The band and frequency will appear on the bottom line of the front

panel and on-screen display (unless you have selected OSD: OFF in the

Input Conﬁguration menu.)

To change the FM tune mode (mono or stereo):



Press TUNE MODE on the remote or the front panel to select the

desired tuner mode.

STEREO

will tune stereo signals.

MONO

will tune either mono or stereo signals. When a station’s signal is

weak in the STEREO mode, selecting mono will often provide a signal

that is more acceptable by switching to the mono sound mode.

Model 970 Operation

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 47 48

Comments to this Manuals

No comments

Outlaw-audio 970 User Manual Page 38

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Outlaw-audio 970